292 D. Tuazon St. 1115 QC, Philippines
(+63-2) 364-3505 to 09
inquiry@boysen.com.ph

PRODUCTS

Boysen® Wallguard™ Dirt Resisting Latex

Introducing a new breed of latex paints that has a very high resistance to dirt, dust, smog and mildew. It can be painted even in a rigorous environment where there is a very high concentration of airborne pollutants.

Boysen® Wallguard™ Dirt Resisting Latex #5715 is suitable to be used near industrial areas and along highways. It is especially suited for repainting medium and high-rise building where the need to maintain a freshly painted look with less maintenance is of prime importance.
 

  • • Highly Resistant to airborne pollutants and dust.
  • • 100% Acrylic
  • • Highly alkaline resistant.
  • • Resist fading, cracking and peeling.
  • • Good exterior durability.
  • • Excellent gloss retention.
  • • Mildew resistant.
  • • Good block and scrub resistance.


Principal uses: Use Boysen® Wallguard™ as an exterior finish for newly constructed building as well as repainting old structures.

PRACTICAL COVERAGE:
Plain finish
25-30 square meters / 4-liters per coat

Textured finish
15-18 square meters / 4-liters per coat

APPLICATION:
Brush, roller or airless spray

SURFACE DRY: 
Thirty (30) minutes

DRY FILM THICKNESS: 
1.5 mils/coat

OVERCOATING INTERVAL: 
Allow one (1) hour before recoating

THINNING: 
Use as supplied. If necessary, thin with not more than ½ liter of water per 4-liter can.

PACKAGING:
4-liter cans

AVAILABILITY:
Semi-Gloss #5715

COLORANTS: Use only Boysen® Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors.

SURFACE PREPARATION:

Concrete
Allow new masonry to dry for fourteen (14) to twenty-eight (28) days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar. Treat with Boysen® Masonry Neutralizer #44 diluted at 1:16 ratio with water. Let stand overnight then rough sand salt residue prior to painting. No need to neutralize in case Boysen® Acrytex™ Primer #1705 is used as primer.

If repainting, remove all loose, scaling, flaking, and peeling off paint by wire brushing, scraping, or rough sanding. When necessary, use Boysen® Paint and Varnish Remover #141 but make sure that residue is completely washed off from the surface to prevent adverse reactions with succeeding coats. Let it dry. Sand smooth painted surfaces for improved inter-coat adhesion.

For chalking old latex paint, apply one (1) coats of Boysen® Chalk Blocker #7304. Let dry overnight. In case of mildew infestation, treat affected areas with a fungicidal wash solution or household bleach mixed with water (1:3, respectively) by swabbing or brushing. Let the treatment overnight before wiping off residue with damp cloth. Let dry.

 

PAINTING SCHEDULE:

1st Coat:
Boysen® Permacoat™ Flat Latex #701 (100% acrylic, waterbased) or 
Boysen® Acrytex™ Primer #1705 (solvent-based acrylic, water-tight)
Let dry for one (1) hour.

Putty:
Boysen® Acrytex™ Cast #1711
Let dry for one (1) hour. Spot prime puttified portions.

Texture:
Boysen® Acrytex™ Cast #1711 (by mortar gun spray)

2nd & 3rd coat:
Boysen® Wallguard™ Dirt Resisting Latex
Let dry for one (1) hour in between coats.

COLORS:

Thalo Blue 
B1404 1:16

Thalo Green  
B1405 1:16

Raw Sienna 
B1406 1:16

Toluidine Red 
B1407 1:16

Burnt Sienna 
B1408 1:16

Burnt Umber 
B1409 1:16

Hansa Yellow 
B1466 1:16

Venetian Red 
B1477 1:16

Lampblack 
B1490 1:16

Thalo Blue 
B1404 
Full Tone

Thalo Green 
B1405 
Full Tone

Raw Sienna 
B1406 
Full Tone

 
 

Toluidine Red 
B1407 
Full Tone

Burnt Sienna 
B1408 
Full Tone

Burnt Umber 
B1409 
Full Tone
 
 

Hansa Yellow 
B1466 
Full Tone

Venetian Red 
B1477 
Full Tone

Lampblack 
B1490 
Full Tone

For technical reasons connected with color reproduction and paint manufacturing, these patterns may not exactly match the paint color.

B5715 Boysen Wallguard Dirt Resisting Latex
 
  • COLOREXPRESS